Auto Parts and Car and Truck AccessoriesQrs Rotary Screw Compressor With Dryer Single Phase 230 V 7.5hp, 60 Gal. Horizontal
Auto Parts - Car and Truck Accessories
Qrs Rotary Screw Compressor With Dryer Single Phase 230 V 7.5hp, 60 Gal. HorizontalThe QRS can be purchased as an HP or HPD (with dryer) The QRS HP and HPD compressors include the following features: Efficient rotary screw compressor 100% continuous duty operation TEFC motor (totally enclosed fan cooled) Full voltage, across-the-line motor starter ASME and CRN approved air tank Tank with moisture drain and safety relief valve LOW SOUND ENCLOSURE Safety devices for - high air/oil temperature - high motor amp draw - fused over current protection - 24v control panel transformer - emergency shutdown On/Off switch with lock-out - oil level sight glass in front panel - UL and UL-C approved control panel - simple electro-pneumatic controls - adjustable belt drive and integral tensioning screw The QRS HPD also includes the following features: Mounted and piped refrigerated air dryer Timer operated moisture drain trap Specifications: Description: Compressor with dryer Starter Wired: Single phase 230V Motor: 1-phase/60Hz Motor Voltage: 220/230V Horsepower: 7.5 Air Delivery (cfm @ 150psig): 21.2 acfm Air Delivery (cfm @ 125psig): 21.5 acfm Operating Pressure: 120-150 psig Max Pressure: 158 psig Horizontal Tank : 60 gal Sound Level Enclosed: 64 dB(A) Dryer Voltage: Single phase/ 115V By Chicago Pneumatic. Plus auto parts car and truck accessories. |
5 Inchx6 Inch Capacity, 1/2 Hp, 1ph, 115/230v Horizontal/Vertical Bandsaw Jet 414458UL listed single phase motor Exclusive design heavy-duty 14-gauge stand Large diameter wheels and built-in handle allows easy movement Front legs feature adjustable leveling pads Ball bearing supported blade wheel Fully adjustable ball bearing blade guides Heat-treated and ground steel worm gear with bronze drive gear Three blade speeds to choose from Automatic shut-off after cut Standard Equipment Vertical worktable Carbon steel blade Adjustable material stop Specifications Round Capacity at 90 (in.) 5 Round Capacity at 45 (in.) 3 Rectangle Capacity at 90 (in./W x H) 5x6 Rectangle Capacity at 45 (in./W x H) 5x3 Throat Depth (in.) 6 Vertical Worktable (in.) 9-5/8 x 9-1/2 Vise Swivels 45 Blade Size (in.) 1/2 x .025 x 64-1/2 Blade Wheel Diameter (in.) 7-3/8 Blade Speeds (SFPM) 80, 120, 200 Bed Height (in.) 25-1/2 Motor 1/2HP, 1Ph, 115/230V, Prewired 115V Floor Space Required (in.) 19x44 Net Weight (lbs.) 115By JET. Plus auto parts car and truck accessories. |
3 Piece Alignment Punch Set 3/16 Inch, 1/4 Inch, 5/16 InchUnbreakable, tough reinforced polymer cap Comfortable grip reduces shock by up to 90% Noise level reduced by up to 80% Striking surface is 2-1/2 times larger Hammer kickback and wrist-elbow trauma minimized Oil resistant cushion grip reduces hot-cold feel Eliminates flying chips and mushrooming of chisel heads Four cap diameters to match hammer sizes The industry s sharpest and most accurate cutting edge Made in U.S.A.By Old Forge Tools. Plus auto parts car and truck accessories. |
Kooler Kleen Transmission Cooling Flush By Dr. Tranny (13.25 Oz.)This convenient oil-based solvent saves time and money for general service and repair shops. It will prevent contaminating new or rebuilt transmissions you install. The flush can is used to prevent transmission contamination by removing and eliminating contaminants such as grease, dirt, sludge, grime and metal shavings in transmission cooling systems and lines, without leaving any water or soapy residue in the system. It also cleans electric parts, wire harnesses, etc. leaving a thin layer of dielectric protectant. Note: This item cannot be shipped via 2nd Day Air Plus auto parts car and truck accessories. |
Frame Rack Unibody ClampBar holes designed for three ways of pulling, using Shackle (#4044) and Oval Loop (#4043). Clamp has recessed pockets to hold bolts stationary for easy tightening. Specifications: Gripping surface: 8 wide (203 mm), 3/4 deep (19 mm) Overall length: 14 1/2 (368 mm) Weight: 19 lbs. (8.62 kg) Capacity: 5 tons (4,536 kg) Replacement Parts: #4045 Nut, Bolt & Washer - #4046 Spring By Mo Clamp. Plus auto parts car and truck accessories. |
Maxsteel 25' X 1 Inch Tape RuleThis MaxSteel Tape Rule has a 25' x 1'' blade 13% thicker blade with patented selective ''cross curve'' technology for 9 feet of standout (1'' blades only). Exclusive cushion grip built into the case for comfortable non-slip grip and impact resistance. Massive bumper designed for increased hook life. Heavier and stronger spring for extra long life and ''smooth-as-silk'' blade recoil. Three rivet corrosion resistant hook moves to allow accurate inside and outside measurements (1'' blades only.) Improved blade readability with high contrast color - easy to read in all light conditions. Top forward blade lock design makes it easier to lock and unlock the blade. Impact-resistant, safety-yellow case. Heavy-duty Mylar polyester film coating extends blade life up to ten times longer.By Stanley Hand Tools. Plus auto parts car and truck accessories. |
Copyright 2004 - 2008 | |